收藏本站
W25Q16DW
DI pin and then driving /CS high. Note that the WEL bit is automatically reset after Power-up and upon
completion of the Write Status Register, Erase/Program Security Registers, Page Program, Quad Page
Program, Sector Erase, Block Erase, Chip Erase and Reset instructions.
/CS
/CS
CLK
Mode 3
Mode 0
0
1
Mode 3
Mode 0
Mode 3
0
1
2
3
4
5
6
7
Mode 3
In structio n
CLK
Mode 0
Mode 0
04h
DI
(IO 0 )
Instruction (04h)
IO 0
IO 1
DO
(IO 1 )
High Impedance
IO 2
IO 3
Figure 7. Write Disable Instruction for SPI Mode (left) or QPI Mode (right)
7.2.9
Read Status Register-1 (05h) and Read Status Register-2 (35h)
The Read Status Register instructions allow the 8-bit Status Registers to be read. The instruction is
entered by driving /CS low and shifting the instruction code “05h” for Status Register-1 or “35h” for
Status Register-2 into the DI pin on the rising edge of CLK. The status register bits are then shifted out on
the DO pin at the falling edge of CLK with most significant bit (MSB) first as shown in Figure 8. The Status
Register bits are shown in Figure 4a and 4b and include the BUSY, WEL, BP2-BP0, TB, SEC, SRP0,
SRP1, QE, LB3-0, CMP and SUS bits (see Status Register section earlier in this datasheet).
The Read Status Register instruction may be used at any time, even while a Program, Erase or Write
Status Register cycle is in progress. This allows the BUSY status bit to be checked to determine when the
cycle is complete and if the device can accept another instruction. The Status Register can be read
continuously, as shown in Figure 8. The instruction is completed by driving /CS high.
/CS
Mode 3
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
CLK
Mode 0
Instruction (05h or 35h)
DI
(IO 0 )
DO
(IO 1 )
*
= MSB
High Impedance
7
*
Status Register 1 or 2 out
6 5 4 3 2 1
0
7
*
Status Register 1 or 2 out
6 5 4 3 2 1
0
7
Figure 8a. Read Status Register Instruction (SPI Mode)
Publication Release Date: September 06, 2012
- 25 -
Revision F
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
W25Q16VSFIG IC FLASH 16MBIT 80MHZ 16SOIC
W25Q32BVZPIG IC SPI FLASH 32MBIT 8WSON
W25Q32DWZEIG IC FLASH SPI 32MBIT 8WSON
W25Q40BWSSIG IC FLASH SPI 4MBIT 8SOIC
W25Q40BWZPIG IC FLASH SPI 4MBIT 8WSON
W25Q64BVSFIG IC SPI FLASH 64MBIT 16SOIC
W25Q64CVZEIG IC SPI FLASH 64MBIT 8WSON
W25Q64DWZEIG IC FLASH SPI 64MBIT 8WSON
相关代理商/技术参数
W25Q16DWSFIP 制造商:WINBOND 制造商全称:Winbond 功能描述:1.8V 16M-BIT SERIAL FLASH MEMORY WITH DUAL/QUAD SPI & QPI
W25Q16DWSNIG 制造商:WINBOND 制造商全称:Winbond 功能描述:1.8V 16M-BIT SERIAL FLASH MEMORY WITH DUAL/QUAD SPI & QPI
W25Q16DWSNIP 制造商:WINBOND 制造商全称:Winbond 功能描述:1.8V 16M-BIT SERIAL FLASH MEMORY WITH DUAL/QUAD SPI & QPI
W25Q16DWSSIG 功能描述:IC FLASH SPI 16MBIT 8SOIC RoHS:是 类别:集成电路 (IC) >> 存储器 系列:SpiFlash® 标准包装:2,500 系列:- 格式 - 存储器:EEPROMs - 串行 存储器类型:EEPROM 存储容量:1K (128 x 8) 速度:100kHz 接口:UNI/O?（单线） 电源电压:1.8 V ~ 5.5 V 工作温度:-40°C ~ 85°C 封装/外壳:8-TSSOP，8-MSOP（0.118"，3.00mm 宽） 供应商设备封装:8-MSOP 包装:带卷 (TR)
W25Q16DWSSIP 制造商:WINBOND 制造商全称:Winbond 功能描述:1.8V 16M-BIT SERIAL FLASH MEMORY WITH DUAL/QUAD SPI & QPI
W25Q16DWZPIG 制造商:Winbond Electronics Corp 功能描述:IC FLASH 16MBIT 104MHZ 8WSON
W25Q16DWZPIP 制造商:WINBOND 制造商全称:Winbond 功能描述:1.8V 16M-BIT SERIAL FLASH MEMORY WITH DUAL/QUAD SPI & QPI
W25Q16V 制造商:WINBOND 制造商全称:Winbond 功能描述:16M-BIT SERIAL FLASH MEMORY WITH DUAL AND QUAD SPI